CCNA 2 v6.0 Routing and Switching Essentials RSE Chapter 3 Exam Online
CCNA 2 v6.0 RSE Chapter 3 Exam Training | |
---|---|
Time | 30 minutes |
Questions | 25 |
Leaderboard: CCNA2 v6.0 Chapter 3 Exam
Pos. | Name | Entered on | Points | Result |
---|---|---|---|---|
Table is loading | ||||
No data available | ||||
CCNA2 v6.0 Chapter 3 Exam
Quiz-summary
0 of 25 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
Information
CCNA2 v6.0 Chapter 3 Exam
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 25 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Average score |
|
Your score |
|
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- Answered
- Review
-
Question 1 of 25
1. Question
1 pointsWhich dynamic routing protocol was developed to interconnect different Internet service providers?
Correct
Incorrect
-
Question 2 of 25
2. Question
1 pointsWhich routing protocol is limited to smaller network implementations because it does not accommodate growth for larger networks?
Correct
Incorrect
-
Question 3 of 25
3. Question
2 pointsWhat two tasks do dynamic routing protocols perform? (Choose two.)
Correct
Incorrect
-
Question 4 of 25
4. Question
1 pointsWhen would it be more beneficial to use a dynamic routing protocol instead of static routing?
Correct
Incorrect
-
Question 5 of 25
5. Question
1 pointsWhen would it be more beneficial to use static routing instead of dynamic routing protocols?
Correct
Incorrect
-
Question 6 of 25
6. Question
1 pointsWhat is a purpose of the network command when configuring RIPv2 as the routing protocol?
Correct
Incorrect
-
Question 7 of 25
7. Question
1 pointsA network administrator configures a static route on the edge router of a network to assign a gateway of last resort. How would a network administrator configure the edge router to automatically share this route within RIP?
Correct
Incorrect
-
Question 8 of 25
8. Question
1 pointsWhat is the purpose of the passive-interface command?
Correct
Incorrect
-
Question 9 of 25
9. Question
1 pointsWhich route would be automatically created when a router interface is activated and configured with an IP address?
Correct
Incorrect
-
Question 10 of 25
10. Question
2 pointsRefer to the exhibit.
CCNA 2 v6.0 RSE Chapter 3 Exam Answers q10
Which two types of routes could be used to describe the 192.168.200.0/30 route? (Choose two.)
Correct
Incorrect
-
Question 11 of 25
11. Question
1 pointsWhat occurs next in the router lookup process after a router identifies a destination IP address and locates a matching level 1 parent route?
Correct
Incorrect
-
Question 12 of 25
12. Question
1 pointsWhich route would be used to forward a packet with a source IP address of 192.168.10.1 and a destination IP address of 10.1.1.1?
Correct
Incorrect
-
Question 13 of 25
13. Question
2 pointsWhich two requirements are used to determine if a route can be considered as an ultimate route in a router’s routing table? (Choose two.)
Correct
Incorrect
-
Question 14 of 25
14. Question
1 pointsWhat is a disadvantage of using dynamic routing protocols?
Correct
Incorrect
-
Question 15 of 25
15. Question
2 pointsWhich two statements are true regarding classless routing protocols? (Choose two.)
Correct
Incorrect
-
Question 16 of 25
16. Question
2 pointsRefer to the exhibit.
CCNA 2 v6.0 RSE Chapter 3 Exam Answers q16
Based on the partial output from the show ip route command, what two facts can be determined about the RIP routing protocol? (Choose two.)
Correct
Incorrect
-
Question 17 of 25
17. Question
1 pointsWhile configuring RIPv2 on an enterprise network, an engineer enters the command network 192.168.10.0 into router configuration mode.
What is the result of entering this command?
Correct
Incorrect
-
Question 18 of 25
18. Question
1 pointsA destination route in the routing table is indicated with a code D. Which kind of route entry is this?
Correct
Incorrect
-
Question 19 of 25
19. Question
1 pointsRefer to the exhibit.
CCNA 2 v6.0 RSE Chapter 3 Exam Answers q19
Which interface will be the exit interface to forward a data packet with the destination IP address 172.16.0.66?
Correct
Incorrect
-
Question 20 of 25
20. Question
1 pointsWhich type of route will require a router to perform a recursive lookup?
Correct
Incorrect
-
Question 21 of 25
21. Question
1 pointsWhich route is the best match for a packet entering a router with a destination address of 10.16.0.2?
Correct
Incorrect
-
Question 22 of 25
22. Question
1 pointsA router is configured to participate in multiple routing protocol: RIP, EIGRP, and OSPF. The router must send a packet to network 192.168.14.0. Which route will be used to forward the traffic?
Correct
Incorrect
-
Question 23 of 25
23. Question
1 pointsWhat is different between IPv6 routing table entries compared to IPv4 routing table entries?
Correct
Incorrect
-
Question 24 of 25
24. Question
3 pointsMatch the dynamic routing protocol component to the characteristic. (Not all options are used.)
CCNA 2 v6.0 RSE Chapter 3 Exam Answers q24
Sort elements
- tables or databases that are stored in RAM
- exchanges routing information and maintains accurate information about networks
- a finite list of steps used to determine the best path
-
data structures
-
routing protocol messages
-
algorithm
Correct
Incorrect
-
Question 25 of 25
25. Question
4 pointsMatch the characteristic to the corresponding type of routing. (Not all options are used.)
CCNA 2 v6.0 RSE Chapter 3 Exam Answers q25
Sort elements
- typically used on stub networks [1]
- less routing overhead [2]
- new networks are added automatically to the routing table [3]
- best choice for large networks [4]
-
[1] static routing
-
[2] static routing
-
[3] dynamic routing
-
[4] dynamic routing
Correct
Incorrect