CCNA 3 v6.0 Scaling Networks SN Chapter 10 Exam Online
CCNA 3 v6.0 SN Chapter 10 Exam Training | |
---|---|
Time | 30 minutes |
Questions | 23 |
Leaderboard: CCNA 3 v6.0 Chapter 10 Exam
Pos. | Name | Entered on | Points | Result |
---|---|---|---|---|
Table is loading | ||||
No data available | ||||
CCNA 3 v6.0 Chapter 10 Exam
Time limit: 0
Quiz-summary
0 of 22 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
Information
CCNA 3 v6.0 Chapter 10 Exam
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 22 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Average score |
|
Your score |
|
Categories
- Not categorized 0%
Your result has been entered into leaderboard
Loading
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- Answered
- Review
-
Question 1 of 22
1. Question
1 pointsA network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?
Correct
Incorrect
-
Question 2 of 22
2. Question
3 pointsRefer to the exhibit.
What three conclusions can be drawn from the displayed output? (Choose three.)
Correct
Incorrect
-
Question 3 of 22
3. Question
1 pointsRefer to the exhibit.
Which conclusion can be drawn from this OSPF multiaccess network?
Correct
Incorrect
-
Question 4 of 22
4. Question
1 pointsWhich OSPF feature allows a remote OSPF area to participate in OSPF routing when it cannot connect directly to OSPF Area 0?
Correct
Incorrect
-
Question 5 of 22
5. Question
3 pointsRefer to the exhibit.
What are three resulting DR and BDR elections for the given topology? (Choose three.)
Correct
Incorrect
-
Question 6 of 22
6. Question
1 pointsWhen checking a routing table, a network technician notices the following entry:
O*E2 0.0.0.0/0 [110/1] via 192.168.16.3, 00:20:22, Serial0/0/0
What information can be gathered from this output?
Correct
Incorrect
-
Question 7 of 22
7. Question
2 pointsRefer to the exhibit.
What two conclusions can be drawn based on the output of the show ipv6 route command? (Choose two.)
Correct
Incorrect
-
Question 8 of 22
8. Question
1 pointsWhich command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?
Correct
Incorrect
-
Question 9 of 22
9. Question
2 pointsA network engineer suspects that OSPFv3 routers are not forming neighbor adjacencies because there are interface timer mismatches. Which two commands can be issued on the interface of each OSFPv3 router to resolve all timer mismatches? (Choose two.)
Correct
Incorrect
-
Question 10 of 22
10. Question
1 pointsA network engineer has manually configured the hello interval to 15 seconds on an interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be affected?
Correct
Incorrect
-
Question 11 of 22
11. Question
1 pointsWhich command can be used to view the OSPF hello and dead time intervals?
Correct
Incorrect
-
Question 12 of 22
12. Question
1 pointsRefer to the exhibit.
A network administrator is configuring OSPF for R1 and R2, but the adjacency cannot be established. What is the cause of the issue?
Correct
Incorrect
-
Question 13 of 22
13. Question
1 pointsRefer to the exhibit.
What the amount of time that has elapsed since the router received a hello packet?
Correct
Incorrect
-
Question 14 of 22
14. Question
2 pointsWhich two parameters must match between neighboring OSPF routers in order to form an adjacency? (Choose two.)
Correct
Incorrect
-
Question 15 of 22
15. Question
1 pointsRefer to the exhibit.
A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem?
Correct
Incorrect
-
Question 16 of 22
16. Question
1 pointsRefer to the exhibit.
R1 and R2 are connected to the same LAN segment and are configured to run OSPFv3. They are not forming a neighbor adjacency. What is the cause of the problem?
Correct
Incorrect
-
Question 17 of 22
17. Question
1 pointsA network administrator is troubleshooting an OSPFv3 configuration on an IPv6 network. The administrator issues the show ipv6 protocols command. What is the purpose for this command?
Correct
Incorrect
-
Question 18 of 22
18. Question
1 pointsRefer to the exhibit.
Directly connected networks configured on router R1 are not being shared with neighboring routers through OSPFv3. What is the cause of the issue?
Correct
Incorrect
-
Question 19 of 22
19. Question
1 pointsAn administrator is troubleshooting OSPFv3 adjacency issues. Which command would the administrator use to confirm that OSPFv3 hello and dead intervals are matching between routers?
Correct
Incorrect
-
Question 20 of 22
20. Question
3 pointsWhat three states are transient OPSF neighbor states that indicate a stable adjacency is not yet formed between two routers? (Choose three.)
Correct
Incorrect
-
Question 21 of 22
21. Question
1 pointsOpen the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which routers are the DR and BDR in this topology?
Correct
Incorrect
-
Question 22 of 22
22. Question
1 pointsOpen the PT Activity. Perform the tasks in the activity instructions and then answer the question.
A network administrator is configuring multiarea OSPFv3 on the routers. The routing design requires that the router RT1 is a DROTHER for the network in Area 0 and the DR for the network in Area 1. Check the settings and status of the routers. What can the administrator do to ensure that RT1 will meet the design requirement after all routers restart?
Correct
Incorrect